How Do I Enable and Use ADB Debugging on Elo Android 7.x Devices?
This article provides the step-by-step procedure required to configure and connect Android Debug Bridge (ADB) debugging on Elo Android 7.x hardware platforms. This includes the Elo I-Series 2.0, PayPoint® Plus for Android, and PayPoint for Android Rev B.
Guide Coverage:
- Recommended Connection: ADB over IP (network-based debugging via Ethernet or Wi-Fi).
- Alternative Connection: ADB over USB (wired debugging and its specific platform limitations).
- Hardware Requirements: Required cables and physical port locations by product line.
⚠️ Critical Qualcomm 625 USB Platform Limitation:
These legacy Android 7.x devices are powered by the Qualcomm APQ8053/MSM8953 (Snapdragon 625) platform. Because the Snapdragon 625 architecture only supports a single active USB controller:
- All USB peripheral ports (e.g., barcode scanners, printers, customer-facing displays) will be entirely disabled while ADB over USB is active.
- Physical Ethernet network connectivity will be disconnected.
👉 Elo strongly recommends using ADB over IP (network connection) to avoid disabling hardware peripherals and maintain active network communication.
Method 1: ADB over IP (Recommended)
This method allows full debugging capabilities over your local network without disabling the device's physical USB peripherals or network adapters.
- Network Connection: Connect your Elo device to your local network using an Ethernet cable or Wi-Fi. Ensure that your host development computer is on the exact same network subnet.
- Access Device Settings:
- From EloView Mode: Press the physical Home + Power buttons simultaneously, enter your administrative password, and navigate to Apps > Settings.
- From Android Home Mode: Open the Android Settings app drawer directly.
- Enable Developer Options: Navigate to Settings > About Phone (or About Tablet). Scroll down to find the Build Number and tap it rapidly seven (7) times. A prompt reading "You are now a developer" will display.
- Enable USB Debugging: Go back to the main Settings menu, open Developer Options, and turn on the toggle for USB Debugging. Select OK to confirm.
- Retrieve IP Address: Go to Settings > About Phone > Status and note the listed IP address.
Establish Network Link: On your host development computer, open a command prompt or terminal window and execute the connection command:
adb connect <device_ip_address>- Authorize Connection: Look at your Elo device screen. Tap Allow when the authorization prompt displays. You can select "Always allow from this computer" to bypass future prompts.
Verify Link: Run the verification commands in your host terminal:
adb devices
adb shell
Method 2: ADB over USB (Alternative)
Use this method only if network debugging is unavailable on your network subnet. Remember that doing so disables all connected USB peripherals and Ethernet.
- Disconnect Cable: Ensure that no USB debugging data cables are connected to the Elo device before starting this process.
- Access Developer Options: Open Android Settings and enable Developer Options (tap Build Number 7 times under About Phone).
Enable Device USB Mode: Navigate to Developer Options and enable:
- USB Debugging
- Switch USB to device mode
Select OK when prompted.
- Connect Hardware: Connect the appropriate physical USB data cable from your host computer to the device's diagnostic port.
Verify Link: Open terminal on your workstation and verify the device is detected:
adb devices
Cable and Port Requirements by Platform
Wired debugging requires specific data cables and ports depending on your Elo hardware platform:
| Elo Hardware Model | Required Cable Type | Physical Diagnostic Port Location |
|---|---|---|
| I-Series 2.0 | USB Type-A to Type-A | Primary Type-A USB port |
| PayPoint Plus for Android / PayPoint for Android Rev B | Mini-USB to USB Type-A | Underneath the baseplate unit, immediately adjacent to the AC power input |
Summary Checklist
- Preferred Protocol: Always connect via ADB over IP to maintain peripheral connectivity.
- Alternative Protocol: Use ADB over USB solely when network linking is blocked by environment policies.
- Hardware Notice: Remember that activating ADB over USB completely severs communication to local cash drawers, built-in receipt printers, scanners, and local Ethernet lines.
Please report any broken links by emailing elo.support@zebra.com and include a link to the knowledge article